HomeFAQs
 
 
Q: What is my range hood size?
A: If you have cabinets on both sides where the range hood will fit in between, then it is the width across from left to right side cabinet. Or when there are no side cabinets, you’ll want to measure the width of your cook stove, or the width of your existing range hood. All sizes are compatible to the U.S. code. Sizes available in 24",30”,36”,42”, and 48”.
Q: Do you have a vent duct?
A: All range hoods requires venting to the outside either through the top or the rear. Rear venting is available in the “SP” stainless steel series. The large 6” or 7” pipe on the top of your existing hood is the top duct or the rectangular 3-1/4” X 10” opening on the rear below the top cabinet is the rear opening.
Q: If I have a microwave range hood, can I replace it with ?
A: Yes. You would need to remove the microwave range hood and mount the range hood underneath the top cabinet.
Q: If I have no cabinet, can I still install the range hood?
A: Yes. PACAIR range hood can be mounted either underneath a top cabinet or on the wall. Please follow the wall mount instruction on the installation user manual.
Basic Trouble-shooting:
Q: What if my range hood will not turn on?
A:

Check your powers to make sure that wire are tightly fastened, cord is plugged it, and there is power to the outlet.
EL Series: due to its safety feature, power will comes on only when the bottom board is tightly closed.

Q: How far does the hood have to be above the cooking surface?
A: The recommended distance from the bottom of the range hood to the cooking surface is 28"~32".
Q: How can I order parts?
A: Please call toll free at 1-800-635-7888 for ordering parts and technical support.
Q: How do I clean the surface of my range hood?
A: Apply any non abrasive cleaner with a slightly damp sponge and rub gently till clean.
Q: What if the range hood appears to be venting poorly?
A:

1. Check that the vent duct at the end isn't obstructed and that the end cap isn't too close to the end of the discharge pipe.  
2. Check that the damper was installed correctly and the flaps operate without obstructions from pipe adapters or other objects.

Q: When both the motors are working, but the light is not:
A: Check light bulbs and the light switch.
Q: When the range hood makes a loud unusual noise when operates:
A: Check the fan blades to make sure it is screw on tightly or try adjusting it lower or try raising it up.
Q: When the motor is moving very slowly when it is first turned on.
A: Check condenser.
 
Q: range hood is certified?
A: range hoods is both UL (United States) and CSA(Canada) approved.
 
 
 
BATHTUB REFINISHING FREQUENT QUESTIONS
 
 





How long will the refinishing last?

It will last as long as you take care of it. Staying on top of the soap is the key. Don't let soap scum start.

Back to top.


What is the difference between BathWorks and the other store bought kits?

BATHWORKS is a commercial refinishing system created by professionals as well as used by professionals. Its extremely thick, durable, glossy coating is unlike ANY store bought products. Most store bought products are thin epoxy based paints, and the finish tends to peel easily and yellow.  BATHWORKS is a 2 part resin, and the resulting finish is a porcelain-like, hard, glossy surface that won't easily, chip, peel, crack, or yellow.


Back to top.


What colors are available to order?

BATHWORKS is available in White, Biscuit, Bone, Almond, and Black.


Back to top.


How long before we can use the bathtub?

Although the Bathtub will feel dry to the touch in about 12 hrs, it is recommended let set for 24 hrs.

Back to top.


What should I use to clean my bathtub after it is refinished?

Any non-abrasive cleaner can be used.  ex.Scrubbing Bubbles, Fantastic, Liquid Ajax.


Back to top.


How Much Does the Standard Kit Refinish?

A single kit has enough material to refinish a standard bathtub (60" x 32") with two coats. We recommend two kits if you are refinishing a tub & tile (the bathtub and three walls around it) or a one piece tub/shower unit. If your looking to refinish the tub/tile and extra tile in the bathroom we recommend three kits.  


Back to top.


How many kits do I need to refinish a Tub/Shower Combination Unit?

For any tub/tile or tub/shower unit we recommend two kits to be on the safe side. Complete the walls with first kit, followed by bathtub with second kit.

Back to top.


Can I refinish the base of a shower?

Absolutely!  Clean base, sand (sandpaper included in kit) and apply Bath-Works DIY kit w/non skid application. In one hour it will look brand new and last for many years.

Back to top.


Can I refinish a shower unit with Bathworks?

Yes, Bathworks DIY Bathtub refinishing kit works wonderful on show units. If you have a tub/shower combination unit two kits are recommended.

Back to top.


Can I change the color of my tub, sink, or tile with Bathworks?

Absolutely!  You can easily change the color of a bathtub, sink, shower, or tile with the Bathworks Kit.  Depending on how much of a contrast there is in color (ie. changing from purple to white) you will likely need to apply multiple coats.  Our standard kits are designed to provide for two coats of a standard size bathtub (60" x 32"). Depending on how different the colors are, you may need to purchase two kits.




Back to top.


Does Bathworks work on Fiberglass?

Yes, the Bathworks DIY refinishing kit works well on fiberglass tubs and showers.


Back to top.


Are the the directions for the DIY Kit online?

Yes.  Please visit this page:




Back to top.


I am interested in refinishing my old bathtub, it is porus and very hard to clean. I also have hard water with lots of calcuim I would like to know all the products I would need to do this?

We recommend our DIY Kit with Non-slip Additive. The non-slip application will help with porous bottom. Drying the bathtub at the drain after each use will help with the calcium, hard water.

Back to top.


Is your product available in stores ?

Our products are  available in stores. You can order online via our online store at 416-828-2956

Back to top.


What is the difference between the non-slip kit for $89.00 and the the slip-guard kit for $49.00?

The difference between kits is the "Slip Guard Kit" is for ONLY the bottom of the bathtub,whereas the "DIY Non-Slip Kit" is for the complete bathtub (it is a full refinishing kit, which includes the slip-guard bottom application).

Back to top.


I have a 40" x 32" fiber glass shower basin with chips that are on the top edge where the shower door was. How much material would i need to fill chips and refinish with a white color?

We recommend our Standard kit W/Non-slip additive and Chip Repair Kit.

Back to top.


Can you ship to Canada? How much will it cost to ship to BC, Canada?

Yes, we can ship globally.  To ship ANYWHERE in Canada is an additional $22 above regular shipping cost. ie To ship a standard kit is $8.50 plus $22 to ship anywhere in Canada.

Back to top.


Can a black sink be refinished with white?

Yes, you can change your black sink to white with BathWorks.

Back to top.


Can your tub refinishing kit work on Cultured Marble tub?

Yes, our DIY kits can be used on Cultured Marble.

Back to top.


Do you have dvd's for the use of your products?

We do not have DVD's for the use of the product. However, we do have videos online, which you can view by clicking the "Videos" link at the top of this page.

Back to top.